深林舞会

  • <tr id='ZAfyVk'><strong id='ZAfyVk'></strong><small id='ZAfyVk'></small><button id='ZAfyVk'></button><li id='ZAfyVk'><noscript id='ZAfyVk'><big id='ZAfyVk'></big><dt id='ZAfyVk'></dt></noscript></li></tr><ol id='ZAfyVk'><option id='ZAfyVk'><table id='ZAfyVk'><blockquote id='ZAfyVk'><tbody id='ZAfyVk'></tbody></blockquote></table></option></ol><u id='ZAfyVk'></u><kbd id='ZAfyVk'><kbd id='ZAfyVk'></kbd></kbd>

    <code id='ZAfyVk'><strong id='ZAfyVk'></strong></code>

    <fieldset id='ZAfyVk'></fieldset>
          <span id='ZAfyVk'></span>

              <ins id='ZAfyVk'></ins>
              <acronym id='ZAfyVk'><em id='ZAfyVk'></em><td id='ZAfyVk'><div id='ZAfyVk'></div></td></acronym><address id='ZAfyVk'><big id='ZAfyVk'><big id='ZAfyVk'></big><legend id='ZAfyVk'></legend></big></address>

              <i id='ZAfyVk'><div id='ZAfyVk'><ins id='ZAfyVk'></ins></div></i>
              <i id='ZAfyVk'></i>
            1. <dl id='ZAfyVk'></dl>
              1. <blockquote id='ZAfyVk'><q id='ZAfyVk'><noscript id='ZAfyVk'></noscript><dt id='ZAfyVk'></dt></q></blockquote><noframes id='ZAfyVk'><i id='ZAfyVk'></i>

                 1、防爆電機不得隨意拆卸;拆卸檢修時,不能用零件的防爆面作撬棒的支點,更↑不允許敲打或撞擊防爆面。

                2、拆卸電機時,應先取下風罩、風扇,再用套管板@ 手拆卸端蓋和軸承蓋的螺栓,接著,用圓木或銅棒沿軸向撞擊軸伸,使端蓋和機座分開,最後取下轉子。拆除零件,防爆面應朝上擱置,並用橡皮或布襯墊蓋上,緊固螺栓,彈簧墊等註意不要丟失。

                3、浸漆和組●裝時,應將防爆面附著的絕緣漆或臟物清洗幹凈,不得用鐵片々等硬物刮劃,但可以用油石研磨不平整的地方。

                4、若防☉爆面損傷,必須用鉛錫焊料HISnPb58-2,焊劑為30%濃度的鹽酸(對鋼制零件)或含錫58~60%的錫」鋅焊料,焊劑為氯化銨30%,氯化鋅70%,加水100~150%混合溶液(對鑄鐵件)進行焊補,焊料與零件的結合要牢固,凸起部分要磨平,達到規定的光潔度。

                5、為防止防爆面生銹,應在防爆面上塗抹♂機油或204-1置ζ 換型防銹油。



                網站權№所有 Copyright © 2010-2011  ICP備案號: